Pressure Wash Driveways: Concrete, Brick, Cement Patio – Cleaning Tips For 2018

Are you stuck on how best you can maintain your driveway in a cost-effective manner? Find out how to pressure wash the mildews, oil, or grease, and end up with a brand-new driveway without paying an arm and a leg.

Let's Pressure Clean Everything Together

If there’s anything that homeowners usually overlook, then it is the driveway. The far one can go is defining the way by paving it with some concrete, asphalt, timber sleepers, or clay bricks. Apparently, paving the driveway seems to be the last nail on the coffin, and then you forget about the maintenance.

Let me put it this way. The driveway is the first sight you bump into as you slam on the brakes of your car. If you want a good impression even when you receive visitors, ensure to clean them at least once or twice a year. Unlike other means of surface maintenance like repairs or replacements, pressure washing is a sure way of reinstating neglected driveways.

Why Should you Pressure Wash your Driveway?

Most people pay little attention to their driveways because they seem to be normal tracks. After all, any dirt will just be washed away by the rain and the cycle continues. However, don’t forget that grease, mildew, grime, and slippery surfaces can only be managed by power washers.

If your neighbor’s driveway appears newer than yours, that ought to be a challenge to you. For realtors, this holds more magnitude since pressure washing is an inexpensive way of enhancing the curb’s appearance. For example, it saves you from fishing out a clean $10000, which could have been wasted on paying for concrete replacement or cleaning services.

7 Quick Steps on Pressure Washing a Concrete Driveway


Requirements

  • A pressure washer

This machine should have an output of more than 2500 PSI because you’re subjecting it to some heavy-duty task on a solid surface. Considering that you’ll need to use a detergent when stripping through grease, make sure the pump has an onboard soap tank.

  • Detergent
  • Degreaser
  • Scrubbing brush
  • Garden hose
  • Water supply
  • Surface cleaner attachment
  • 25-degree and 65-degree nozzle tips
  • Safety gloves

Method


Step 1: Refer to the manual

Read through the safety manual of the pressure washer to know what is required of you. These pumps differ in terms of setting up and how they operate.

Step 2: Clear the area

Remove excess dirt, toys, pebbles, debris, vehicles, and any other clutter that might interfere with the cleaning process. You should also consider protecting the exterior walls and the landscaping plants against the high water pressure that would otherwise damage them.

Step 3: Prepare the surface

Use a spray degreaser to lift up any stubborn grease or oil spillages. As part of the preparation process, manually scrub the visible mildew with a brush.

Step 4: Set up the pressure washer

The user manual will guide you on how to assemble the pump. Attach the green-colored25-degree nozzle, a spray wand, and the garden hose. When everything is ready, connect the hose to a water supply, and turn it on.

Step 5: Apply the detergent

Double check the manual to see if the manufacturer has recommended a specific cleaning solution for the pressure washer. Fill the detergent tank with the soap and dip in the siphon tube, which is supplied with the pump.
Put on the gloves, connect a 65-degree nozzle, and release the soap solution. Hold down the spray handle while maintaining a distance of about 10 inches from the concrete. As you move back and forth, ensure that each stroke overlaps the other by approximately seven inches.
Allow the detergent to soak the mildew, dirt, grease, and oil for at least five minutes.

Step 6: Pressure-wash the concrete

Replace the soap applicator tip with a rotary nozzle. Hold down the spray gun about five inches from the surface. For tougher stains, move as close as three inches from the concrete floor. Move with still strokes as you move back and forth to ensure you cover every spot.
Alternatively, use a surface cleaner attachment for rapid cleaning. This attachment covers a wider area, minimizes the possibility of surface damage, and accelerates the removal of dirt. Depending on your budget and the specifications of the surface cleaner, you can part with as low as $20 or a high-end model going for $2000.

Step 7: Rinse

Attach the 25° nozzle tip and give the surface a final rinse, which should wash out the detergent.

Pressure Washing Driveway Quick Tips


  1. Safety first! Wear protective eyeglasses and gloves.
  2. Always pressure-wash at the onset of spring for fast drying and preventing the build-up of ice.
  3. Wash your driveway at least twice or once a year.
  4. To make the driveway more appealing than just a mere wash, apply a waterproof sealer.
  5. Be mindful of the environment by restraining the wash water from entering the storm drain. These waste solutions contain chemicals, detergents, or grease that are likely to pollute the local stream. Unless you live near a sani-sewer, push the waters to the lawn, allow it to dry, and vacuum up the residues.
  6. Always refer to the user manual.

Stepwise Tutorial on How to Pressure-wash a Brick Driveway

This procedure is slightly similar to the one above except that it deviates after the fourth step.

Step 1: Read through the manual

Step 2: Clear out the area and prepare the surface

Step 3: Set up the washer

Step 4: Soak the driveway

This sounds odd, right? First, let me explain. Brick surfaces have a high absorption rate. For example, if you were spraying some detergent along the driveway, there will be no evidence of soap even before you cover the midway stretch. It is for this reason that you ought to wet the brick driveway, preferably with a 40-degree nozzle.

Step 5: Apply the detergent

Use the soap applicator nozzle to spray the soap. Ensure the entire surface is covered with soap, leaving a margin of about 5 – 8 inches from each stroke. Leave the detergent to work on the surface for about five minutes.

Step 6: Strip dirt from the concrete

Attach the 25° jet tip to rinse out the detergent and all the dirt. The pressure should not be too high as to damage the mortar.

It’s Time To Watch Video

Which is The Right Pressure Washer for Cleaning The Driveway?


With pressure washers, you just can’t lack an option. However, the problem comes in when you’ve got to select from the over 20 brands of pressure cleaners and more than 500 choices.

The Cleaning Power: Light-duty vs Medium-duty

A power washer is always defined by its cleaning power, a value that corresponds to the PSI and the flow rate. Take, for example, a pump with 2400PSI and a rate of 2GPM will clean faster and powerfully than a light-duty pump with 1500 PSI. Check out the best medium-duty for cleaning your filthy driveway.

Gas vs Electric-powered

The choice will depend on one’s preference because each one of these pumps comes with different pros and cons.

A gas pressure washer has a higher cleaning power. For instance, if it takes you half an hour to wash a driveway with a gas pump, then be sure the time will triple with an electric cleaner. Besides the portability and rapid cleaning, these pumps require regular maintenance, are expensive, bulky, noisy, and emit gasoline fumes.

On the other hand, electric-powered washers are cost-friendly, lighter, and operate quietly. However, they’re less powerful and less portable due to the electric cord and the need for a power outlet. Unless you’ve got longer cables or several sockets along your driveway, you shouldn’t buy an electric washer.

Buying vs Hiring

A good pressure washer will cost you $300 to $500. If you were to hire this pump instead, the charges may accrue up to $150, inclusive of the deposits and security. Just buy the machine and forget everything.

Hot vs Coldwater

This aspect hinges on your budget. If you can’t part with $1000 for a cut-rate hot-water pump, then buy a $300 cold-water model. I would go with a hot because it cleans faster and thoroughly especially through the grease and oil spillages.

The Best Machine for Cleaning a Concrete or Brick Driveway

Forget about the high-ratings and the popularity associated with the Simpson’s Megashot Model. Here are some of the reasons why I fall for this washer.

Affordable

Considering the many features it has, the Megashot is inexpensive and a value for your money.

High-powered pump

Boasting a pressure of 3200PSI at a flow rate of 2.5GPM, the MSH3125-S Megashot pressure washer can handle both medium and heavy-duty tasks. You can use it for commercial purposes or for domestic applications.

Powerful Honda-powered Engine

This engine works smoothly and quietly. Besides, maintaining it is quite a breeze.

Compact

Gas-powered pressure washers are always heavy but this one is different. At 65 pounds, the pump is inarguably lightweight compared to other models and brands. It has a compact design and slightly smaller than a wheelbarrow. To enhance portability, the washer comes with sturdy 10” pneumatic wheels for ease of maneuverability.

Final Verdict


Maintaining a clean driveway is not as hard as it seems. Practically, pressure washing is the best alternative. Suppose you’re to wash a driveway, which accommodates up to four vehicles. The shortest time you’ll take is 30 minutes, although you can spend as much as two hours depending on the intensity of dirt and the type of pressure washer in use. Try out the Simpson MSH3125-S pump and you’ll be done with cleaning in less than an hour. Pressure-washing your concrete driveway will give it a new look rather than having it reconstructed.